Dissociation


Dissociation

When the analyte in the flow over the surface of the chip is replaced by the flow buffer, the free concentration of the analyte suddenly drops to zero and the complex will start to dissociate. If rebinding of released analyte can be ignored, dissociation can be described by the rate equation (1):

eqDiss1
Dissociation rate equation

or the linearized form

eqDiss2
Linearized dissociation
SenDis1
Dissociation

In theory, the dissociation rate constant (kd) is given by the intercept on the ordinate when the slope of the association phase of dR/dt versus R is plotted against C. In practice, however, this intercept is too close to the origin to be determined with accuracy. Dissociation rate constants can be more reliably measured from the dissociation of the analyte from the ligand after buffer replaces the analyte solution (2).

Like the association it is better / easier to fit the integrated rate equation to the experimental data:

eqDiss3
Integrate rate equation
GraphDiss1
Dissociation graph

When at t → ∞ the sensorgram has not returned to zero, it is possible to take this value in the equation (3). The Evaluation software gives the value (Offset), which means the deviation from zero at t → ∞ .

eqDiss4
Dissociation + offset

The pure kinetic 1:1 dissociation in an ln(R0/Rt) vs. tt-t0 plot is a straight line while mass transport limited dissociation has a downward curvature. However heterogeneity in analyte or ligand (4), (5) or rebinding of analyte (6) can also cause this kind of plot.

GraphDiss2
Dissociation graphs

Due to immobilization of the ligand and introduction of sites with different affinities, low affinity sites are only occupied when the system reaches equilibrium at Rmax. Then dissociation is not a single exponential decay and can be better described by a double exponential decay (3).

Sometimes analyte diffusion out of the matrix can give rise to non-single exponential decay. In addition, rebinding can obscure single exponential decay or lower the dissociation rate constant.

Complex half life time

The complex half-life time is the time needed to let dissociate half of the complexes to their individual components (4).

eqDiss5
Complex half time

A strong binding (kd> 10-4s-1) is difficult to analyze when the dissociation curve is to short. As a rule of thumb, the dissociation curve should decrease at least 5% before analysis is attempted. For a dissociation constant of 10-4s-1 this will result in a dissociation time of at least 12 minutes. In addition, sufficient blank injections with the same long "dissociation" times are needed to compensate for possible baseline drift (8).

Long dissociation times are not practical when done with every injection. Instead, use the long dissociations for the highest injected analyte concentrations (8) and use for the other concentrations a short dissociation time (200 - 300 s). However, it is important to avoid analyte concentration that can introduce artefacts such as non-specific binding, steric hindrance or aggregation.

References

(1) Graphpad SoftwareGraphpad Prism. (1998).
(2) BIACORE ABApplication note 301. Bia note(1998).
(3) O'Shannessy, D. J. et alDetermination of rate and equilibrium binding constants for macromolecular interactions using surface plasmon resonance: use of nonlinear least squares analysis methods. Analytical Biochemistry212: 457-468; (1993).
(4) BIACORE ABBIACORE Technology Handbook. (1998).
(5) Morton, T. A. et alInterpreting complex binding kinetics from optical biosensors: a comparison of analysis by linearization, the integrated rate equation, and numerical integration. Analytical Biochemistry227: 176-185; (1995).
(6) van der Merwe, P. A. et alAffinity and kinetic analysis of the interaction of the cell adhesion molecules rat CD2 and CD48. EMBO J.12: 4945-4954; (1993).
(7) BIACORE ABKinetic and affinity analysis using BIA - Level 1. (1997).
(8) Katsamba, P. S. et alKinetic analysis of a high-affinity antibody/antigen interaction performed by multiple Biacore users. Analytical Biochemistry352: 208-221; (2006).